Delrin Front Motor Mount for Mitsubishi / Mopar 24V 3.0L

Delrin Front Motor Mount for Mitsubishi / Mopar 24V 3.0L
Delrin Front Motor Mount for Mitsubishi / Mopar 24V 3.0L
Delrin Front Motor Mount for Mitsubishi / Mopar 24V 3.0L

Delrin Front Motor Mount for Mitsubishi / Mopar 24V 3.0L

Regular price $65.00
/
All products are entirely MADE IN THE USA unless specifically stated.

FREE Priority Shipping on all orders over $35 to the continental US.
Standard shipping charges will apply to the rest of the world.
This is a solid Delrin (Acetal) front motor mount for SOHC (24-valve) 3.0L V6 equipped Mitsubishi / Mopar vehicles.


The mount is installed just as the stock mount. Once on the car, it looks stock, unless one knows what to look for. Installation is the same as replacing a stock mount.

The stock mounts are a very weak piece. As shown below, the rubber insert is only held on by two small strips of rubber, allowing a lot of engine movement. With an engine of this much torque, the mounts take a massive amount of abuse, and will not last long. Many of these stock mounts have been completely torn in half, resulting in severe wheel hop, damage to CV joints, and thumping sounds from under the hood.

Delrin (Acetal) motor mounts, transmission mounts, and bushings are each machined from a solid blocks, and have either Stainless Steel or Aluminum bushings fit into the mounts to act as a point of contact for the connecting bolts when required. Delrin is an extremely strong and stiff plastic. It is commonly used in place of metal in applications where metal can not be used (magnetic, corrosion, or conducting / insulating reasons). These are much stiffer than polyurethane mounts, and it will not give or wear out. Delrin mounts should never need to be replaced, unlike the stock units which are usually considered a wear item.

Delrin mounts minimize the jumping or twisting of the motor under the hood. This movement is caused by the rotating mass of the crankshaft and transmission components. With stock mounts, the engine will twist itself in the engine bay when the throttle is opened, or during high-speed shifts. Over time, this force will destroy the stock rubber mounts. When this happens, the rubber may split or rip, allowing the engine to potentially move inches back and forth. This can destroy CV joints, other mounts, and create wheel-hop.

With our mounts, shifts will be much crisper. While pressing the gas pedal, a vehicle is much more responsive; as the motor does not lose as much torque twisting into the mounts.

At a price usually less than that of inferior stock mounts, these are not only a great performance item, but a bargain for each application.

Almost any item here can be customized to better fit your needs. Extra charges may apply, but we will do our best to make it happen. Please contact us for details.


Shipping is FREE on all orders over $35 to the continental US.
Standard shipping charges will apply to the rest of the world.
More from Automotive
Rear Main Seal Installation Tool for Porsche
Rear Main Seal Installation Tool for Porsche
Rear Main Seal Installation Tool for Porsche
Plasmatio
$45.00
Delrin Rear Motor Mount for Toyota 1MZ-FE
Delrin Rear Motor Mount for Toyota 1MZ-FE
Delrin Rear Motor Mount for Toyota 1MZ-FE
Plasmatio
$80.00
Aluminum Suspension Rear Brace for Porsche
Aluminum Suspension Rear Brace for Porsche
Aluminum Suspension Rear Brace for Porsche
Plasmatio
$115.00
Audi / Porsche / VW Clutch Alignment Tool
Audi / Porsche / VW Clutch Alignment Tool
Audi / Porsche / VW Clutch Alignment Tool
Plasmatio
from $1.00
Jeep JK(U) Freedom Panel Wrench
Jeep JK(U) Freedom Panel Wrench
Jeep JK(U) Freedom Panel Wrench
Plasmatio
$25.00
Delrin Motor Mount Set for Yamaha V-Max
Delrin Motor Mount Set for Yamaha V-Max
Delrin Motor Mount Set for Yamaha V-Max
Plasmatio
$85.00
Recently viewed